Caple DF625 Instruction Manual

Instruction Manual Model 2017-95 Up/DownconverterDecember 2009 Rev. 0MENUEXECUTEMODEL 2017CROSS TECHNOLOGIES INC.U F

2.2 Rear Panel Input/Output Signals and Control - Figure 2.1 shows the input and output connectors on the rear panel.ACGNDJ18J2RF IN10 MHZ REF

2.3 Front Panel Controls and Indicators - The following are the front panel controls and indicators.MENUEXECUTEU F= 475 G=+10MUTE REMOTEALARM P

2.4 Installation / Operation2.4.1 Installing and Operating the 2017-95, Upconverter Section1.) Connect a -40 dBm to -10 dBm signal to IF In, J4 (F

FUSE DRAWERSPARE FUSE DRAWERAC Fuse - 2 amp slow blow (Type T 2A GDC), 5 mm X 20 mm~INPUT100-240± 10%VAC47-63 Hz2A MAXFUSETYPE T 2A GDC250 VOLTFOR

2.5 Menu Settings2.5.1 Functions - This section describes operation of the front panel controls. There are three operator switches, the LCD display

2.5.2 Power-On SettingsNOTE: THE LAST STATUS OF A UNIT IS RETAINED EVEN WHEN POWER IS REMOVED. WHEN POWER IS RESTORED, THE UNIT WILL RETURN TO IT&a

2.5.4 Frequency ChangesAt any time during the modification process, if you have made a mistake and do not wish to save the changes you have made, do

2.5.5 Gain ChangesWhen you get to this menu note that the gain changes will be made as you make them but if you do not wish to save the changes you h

2.5.5.2 Downconverter GainTo set the Downconverter gain, first push the Menu/Execute switch to get to the gain setting:Operate the Menu/Execute switc

ON POWER UPNORMAL DISPLAYPUSHING MENU/EXECUTE SEQUENCEREV 1.00U F = 475 G = +10.0D F = 625 G = +25.0UP F = 475SCROLL <>SCROLL PUSH B

INSTRUCTION MANUALMODEL 2017-95 Up/Downconverter TABLE OF CONTENTS PAGEWarranty 21.0 General 31.1 Equipment Description 31.2 Technical Characteristi

CROSS TECHNOLOGIES, INC.6170 Shiloh RoadAlpharetta, Georgia 30005(770) 886-8005FAX (770) 886-7964Toll Free 888-900-5588WEB www.crosstechnologies.com E

MODEL 2017-95 Up/Downconverter1.0 General1.1 Equipment Description The 2017-95 L-band Up/Downconverter converts 70 MHz to 250-950 MHz (Up) and 250-9

1.2 Technical CharacteristicsTABLE 1.0 2017-95 Up/Downconverter Specifications*--------UPCONVERTER--------Input Characteristics (IF)Impedance/Return

1.3 Monitor and Control InterfaceA) Remote serial interfaceProtocol: RS-232C, 9600 baud rate, no parity, 8 data bits, 1 start bit, and 1 stop bit.

B) Status Requests Table 1.1 lists the status requests for the 2017-95 and briefly describes them.* PLEASE NOTE: The two character {aa}(00-31) prefix,

C) Commands Table 1.2 lists the commands for the 2017-95 and briefly describes them. After a command is sent the 2017-95 sends a return “>” indica

1.4 Environmental Use InformationA. Rack-Mounting - To mount this equipment in a rack, please refer to the installation instructions located in the u

2.0 Installation2.1 MechanicalThe 2017-95 consists of one RF/Controller PCB housed in a 1 RU (1.75 inch high) by 16 inch deep chassis. A switching,